unisonic technologies co., ltd UC1108 preliminary cmos ic www.unisonic.com.tw 1 of 8 copyright ? 2015 unisonic technologies co., ltd qw-r103-098.a low-power off-line primary side regulation controller ? description the utc UC1108 is a primary control unit for switch mode charger and adapter applications. the contro lled variable is transferred by an auxiliary winding from the secondar y to the primary side. the device uses pulse frequency modulation (pfm) method to build discontinuous conduction mode (dcm) flyback power supplies. the utc UC1108 operates in primary-si de sensing and regulation. opto-coupler and tl431 could be eliminated. it also eliminates the need of loop compensation circuitry while maintaining stability. the UC1108 achieves excellent regulation and high average efficiency, yet meets the requirement for no-load co nsumption less than 30mw. the utc UC1108 has the built-in programmable cable voltage drop compensation function, which ma ke it flexible to accommodate various cables with different gauges and lengths the utc UC1108 achieves high precisi on cv/cc regulation and high power efficiency. it offers comprehensive protection coverage with auto-recovery features including cycle-by-cycle current limiting, output over voltage protection, f eedback loop open protection, short circuit protection, leading edge blanking, v cc under voltage lockout, etc. ? features * 30mw no-load input power * primary side control for eliminating opto-coupler and secondary cv/cc control circuitry * proprietary cc tightening technique to achieve vertical cc profile * programmable output cable voltage drop compensation * compensation for external co mponent temperature variations * random frequency adjustment to reduce system emi * flyback topology in dcm operation * built-in soft start * over voltage protection * short circuit protection sop-8 ? ordering information ordering number package packing UC1108g-s08-r sop-8 tape reel UC1108g-s08-r (1)packing type (2)package type (1) r: tape reel (2) s08: sop-8 (3) g: halogen free and lead free (3)green package
UC1108 preliminary cmos ic unisonic technologies co., ltd 2 of 8 www.unisonic.com.tw qw-r103-098.a ? marking ? pin configuration ? pin description pin no. pin name description 1 cs the primary current sense 2 v cc supply voltage 3 out this pin drives the base of external power npn switch 4 gnd ground 5 cpc this pin connects a capacitor for output cable compensation 6 fb the voltage feedback from the auxiliary winding 7 cpr connects a resistor to fb pin for adjustable output cable compensation 8 bias this pin sets the bias current inside UC1108 with an external resistor to gnd ? block diagram
UC1108 preliminary cmos ic unisonic technologies co., ltd 3 of 8 www.unisonic.com.tw qw-r103-098.a ? absolute maximum rating parameter symbol ratings unit voltage at v cc pin to gnd -0.3~36 v voltage at cs, out to gnd -0.3~7 v fb input -40~10 v output current at out internally limited a operating junction temperature t opr 150 c storage temperature t stg -65~150 c note: absolute maximum ratings are those values beyond which the device could be permanently damaged. absolute maximum ratings are stress ratings only and functional device oper ation is not implied. ? thermal resistance s characteristics parameter symbol rating unit junction to ambient ja 190 c/w ? electrical characteristics (v cc =15v, t a =25c, unless otherwise specified.) parameter symbol test conditions min typ max unit uvlo section start-up threshold v th (st) 17 18.5 21 v minimal operating voltage v opr (min) 8.2 9.2 10.2 v reference voltage bias pin voltage v bias r bias =200k ? , after turn on 1.0 1.1 1.2 v standby current section start-up current i st v cc =v th (st) -0.5v, r bias =200k ? ,before start-up 0.6 a operating current i cc(opr) r bias =200k ? 390 480 a drive output section out maximum current source i out r bias =200k ? 28 36 44 ma current sense section current sense threshold v cs 490 513 535 mv pre-current sense v cs(pre) 390 413 435 mv leading edge blanking 500 ns feedback input section feedback pin input leakage current i fb v fb =4v 1.8 2.4 3.0 a feedback threshold v fb 3.97 4.03 4.09 v enable turn-on voltage v fb(en) -2.0 -1.7 -1.4 v output voltage compensation section cpr voltage v cpr dons (tons/t): from 55% to 0.02% 1.5 3.5 v cpr sink current i cpr 200 a protection section over voltage protection v fb(ovp) 7 8 9 v
UC1108 preliminary cmos ic unisonic technologies co., ltd 4 of 8 www.unisonic.com.tw qw-r103-098.a ? operation description the utc UC1108 is a primary control unit for switch mode char ger and adapter applications. it operates in primary-side sensing and regulation. opto-coupler and tl43 1 could be eliminated. proprietary built-in cv and cc control can achieve high precision cv/cc performance. it uses pulse frequency modulation (pfm) method to build discontinuous conduction mode (dcm) flyback power supplies. startup control the voltage regulator provides the internal power supply v dd . for v cc and v dd external capacitors are required. the current biasing of utc UC1108 is adjustable by an external resistor. internal time constants, thresholds and the output current depend from the va lue of this resistor. the startup circuit activates the ic after startup and deactivates the ic in case of uvlo. operating current the operating current of utc UC1108 is as low as 400ua. good efficiency and very low standby power can be achieved. constant voltage operation the output voltage is defined by the transmission ratio between the secondary and auxiliary winding. the utc UC1108 captures the auxiliary winding feedback voltage at fb pin and operates in const ant-voltage (cv) mode to regulate the output voltage. the auxiliary voltage reflects the output voltage is given by: ) v ? + v ( n n = v o s a aux (1) where v indicates the drop vo ltage of the output diode. figure2. auxiliary voltage waveform via a resistor divider connected between the auxiliary winding and fb, the v aux is sampled at the tsampling end and it is hold until the next sampling. the sampled voltage is compared with 4v reference voltage and the error is amplified. the error amplifier output re flects the load condition and controls the toff time to regulate the output voltage, thus constant output voltage can be achieved.
UC1108 preliminary cmos ic unisonic technologies co., ltd 5 of 8 www.unisonic.com.tw qw-r103-098.a ? operation description (cont.) constant current operation when the sampled voltage is below 4v reference volt age and the error amplifier out put reaches its maximum, thus utc UC1108 operates in constant-current (cc) mode. the cc point and maximum output power can be externally adjusted by external current sense resistor r cs. the larger rcs, the sma ller cc point is, and the smaller output power becomes. figure3. adjustable output power by changing rcs figure4. secondary current waveform in cc operation, the cc loop control function of utc UC1108 will keep a fixed proportion between secondary inductance de-magnetization time (tdemag) and switch ing cycle time (tsw). the fixed proportion is 7 4 = tsw tdemag (2) thus the output current is given by: ipk n n 7 2 = tsw tdemag ipk n n 2 1 = iout s p s p (3) current sensing and leading edge blanking cycle-by-cycle current limiting is offered in utc UC1108 . the switch current is detect ed by a sense resistor into the cs pin. when the power switch is turned on, a turn-on spike will occur on this resistor. a 500ns leading-edge blanking is built in to avoid false-termi nation of the switching puls e so that the external rc filtering is no longer needed. drive bjt the driver is a push pull stage with the supply voltage v cc . it provides the driving current for the external power bipolar transistor. the output signal is current-limited to i out(source) .
UC1108 preliminary cmos ic unisonic technologies co., ltd 6 of 8 www.unisonic.com.tw qw-r103-098.a ? operation description (cont.) output cable compensation the utc UC1108 senses the auxiliary winding feedback voltage at fb pin and operates in constant-voltage (cv) mode to regulate the output voltag e. in cv mode, fb pin voltage v fb is a constant of 4. 0v. the cpr pin voltage v cpr is generated by the internal circuit of utc UC1108 . it linearly decreases with the rise of the output load directly. where dons is the duty cycle of secondar y diode, and is equal to tdemag/tsw, wh ich is directly proportional to the output loading. the maximum dtdemag is 4/7 and the minimal dtdemag is cl ose to zero in cv mode of utc UC1108 . protection control good power supply system reliability is achieved with its comprehensive protection features including output over-voltage protection, feedback loop open protection, cycl e-by-cycle current limiting, short circuit protection, leading edge blanking and uvlo, etc. v cc is supplied by transformer auxiliar y winding output. the output of utc UC1108 is shutdown when v cc drops below v th(off) and the power converter enters powe r on start-up sequence thereafter.
UC1108 preliminary cmos ic unisonic technologies co., ltd 7 of 8 www.unisonic.com.tw qw-r103-098.a ? typical application circuit (5v/1a) bom reference component reference component bd1 bd 1a/600v r2 r 6.8m ? 1206 5% l1 inductor, com-choke r3 r 6.8m ? 1206 5% c1 ec 4.7u f 400v 105c r4 r 30k ? 0805 1% c2 ec 4.7u f 400v 105c r5 r 9.1k ? 0805 1% c3 cc 2.2u f 50v 105c r6 r 27k ? 0805 5% c4 cc 0.47u f 50v 0805 r7 r 200k ? 0805 5% c5 cc 1n f 1000v 1206 r8 r 1.0 ? 1206 5% c6 ec 1000u f 10v 105c r9 r 200k ? 1206 5% d1,d2 diode utc 1n4007 t1 ee-16 d3 diode utc sb340 f1 fuse 1a 250vac r1 r 2.4k ? 1206 5% q1 npn transistor utc mje13003
UC1108 preliminary cmos ic unisonic technologies co., ltd 8 of 8 www.unisonic.com.tw qw-r103-098.a utc assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all utc products described or contained herein. utc products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
|
